Reparatur, Ersatzteile, Technischer Support: 0049 (0) 98 72 / 95 66 61 0
Reparatur, Ersatzteile, Technischer Support: 0049 (0) 98 72 / 95 66 61 0

PROMAC PBD-2870 Metalldrehmaschine

Bilddaten:

PBD-2870.tif
Tagged Image File [74.4 MB]
PBD-2870.jpg
JPG-Datei [529.6 KB]
PROMAC PBD-2870 .jpg
JPG-Datei [802.7 KB]

Bilddaten:

PBD-2870_Figure 5-1.jpg
JPG-Datei [55.5 KB]
PBD-2870_Figure 5-2.jpg
JPG-Datei [51.3 KB]
PBD-2870_Figure 5-3.jpg
JPG-Datei [34.2 KB]
PBD-2870_Figure 8-1-0.jpg
JPG-Datei [27.1 KB]
PBD-2870_Figure 8-1-1.jpg
JPG-Datei [22.4 KB]
PBD-2870_Figure 8-2.jpg
JPG-Datei [62.3 KB]
PBD-2870_Figure 8-4.jpg
JPG-Datei [44.6 KB]
PBD-2870_Figure 9-1.jpg
JPG-Datei [43.5 KB]
PBD-2870_Figure 10-6.jpg
JPG-Datei [38.8 KB]
PBD-2870_Figure 10-7.jpg
JPG-Datei [25.1 KB]
PBD-2870_Figure 10-8.jpg
JPG-Datei [30.8 KB]
PBD-2870_Figure 10-9.jpg
JPG-Datei [32.8 KB]
PBD-2870_Figure 11-1.jpg
JPG-Datei [36.5 KB]
PBD-2870_Figure 11-3.jpg
JPG-Datei [30.1 KB]
PBD-2870_Figure 11-4.jpg
JPG-Datei [36.8 KB]

- Automatischer Längsvorschub
- Stufenlose, elektronische Drehzahlregulierung
- Integriertes Kühlmittelsystem
- Integrierte Maschinenleuchte
- Inkl. Maschinensockel

 

 

 

 

 

 

 

 

 

Figure 5‐1: Machine description
A ............................................ Machine cabinet stand
B .................................................................. Gear box
C ..............................................................Pulley cover
D ............................................................... Headstock
E ............................................ Chuck and chuck guard
F .................................. Tool post and tool post guard
G ......................................................... Machine lamp
H ........................................................ Coolant nozzle
I .................................................................... Top slide
J ..................................................................... Carriage
K ................................................................... Tailstock
L ............................................................ Splash guard
M ............................................................... Lathe bed
N .............................................................. Lead screw
O .................................................................. Chip tray
P ....................................................................... Apron
Q .................................................... Anchor bolt holes

 

 

 

 

 

 

 

 

 

Figure 5‐2: Machine description
R ........................................... Feed speed select knob
S ........................................ Feed forward/off/reverse
T ...................................................... Coolant ON/OFF
U ............................................ Spindle power ON/OFF
V ......................................... Spindle forward/reverse
X .......................................................Emergency Stop
Y ................................................... Apron hand wheel
Z ............................................ Cross slide hand wheel
AA ......................................................... Half nut lever
BB ............................................ Top slide hand wheel
CC ........................................................ Threading dial

 

 

 

 

 

 

 

 

 

Figure 5‐3 Machine description
VV ......................................................... Top slide lock
XX ...................................................... Cross slide lock
YY ................................... Top slide taper adjustment
ZZ ........................................................... Carriage lock

8.1 Changing spindle speed
The speeds of the lathe are controlled by the position of the
belt on the pulleys (Fig 8‐1).

Figure 8‐1: Spindle speed chart

Figure 8‐2: Change gear setup

Remove the pulley cover.
The rotational speed of the lead screw, and hence the rate of
feed of the cutting tool, is determined by the gear
configuration and by the feed speed select lever (R, Fig 5‐2).
Assemble the gears with desired setup (Fig 8‐2)

 

 

 

 

Adjust gears to mesh with upper and lower gear.
Placing ordinary paper in between gears helps to adjust for
correct gear spacing (… remove the paper afterwards!).
Reinstall the pulley cover

Figure 8‐4: Taper turning with top slide

 

By angling the top slide, tapers may be turned.
Loosen two hex nuts (A, Fig 8‐4) and rotate the top slide
according to the graduated scale (B).

Refer to Figure 9‐1:
R ............................................. Feed select knob
S ............................... Feed forward/off/reverse
T .............................................. Coolant ON/OFF
U .................................. Spindle power ON/OFF
V ................................. Spindle forward/reverse
X .............................................. Emergency Stop

Figure 10‐6: Machine controls

 

Apron travel (Y, Fig 10‐6), cross travel (Z) and top slide travel
(BB) can be operated for longitudinal and cross feeding

 

The correct feed depends on the material to be cut, the cutting
operation, the type of tool, the rigidity of the work piece
chucking, the depth of cut and the desired surface quality.

Figure 10‐7: Available feed rates
For example:
Operation feed/rev feed select knob
Stock removal 0,28mm .............................. III
Finishing cut 0.14mm ............................... II
Micro finishing cut 0.07mm ................................ I
NOTE: Three additional feed rates are available with different
change gear setup (Fig 10‐7).

Figure 10‐8: Threading Dial

Figure 10‐9: Threading dial setup

 

Note:
For thread pitches of 0,2/0,3/0,5/0,6/0,75/ 1,0/ 1,5/3 mm the
half nut can be engaged at any point.
(lead screw pitch = 3 mm = can be divided by thread pitch).

Figure 11‐1: Gearbox oil fill‐up

Figure 11‐3: Slide adjustment

Figure 11‐4: Cross slide spindle adjustment

Optionales Zubehör / optional accessories:

PBD-2870_Zubehoer.pdf
PDF-Dokument [1.9 MB]

Bedienungsanleitung / Manual:

Ersatzteilliste / Part List:

PBD-2870_Manual_EN_07-2017.pdf
PDF-Dokument [6.1 MB]

Sollten Sie weitere Fragen haben, zögern Sie nicht uns zu kontaktieren.

 

Should you have any further questions, please do not hesitate to contact us.

Ihre Formularnachricht wurde erfolgreich versendet.

Sie haben folgende Daten eingegeben:

Kontaktformular

Bitte korrigieren Sie Ihre Eingaben in den folgenden Feldern:
Beim Versenden des Formulars ist ein Fehler aufgetreten. Bitte versuchen Sie es später noch einmal.

Hinweis: Felder, die mit * bezeichnet sind, sind Pflichtfelder.

Hier finden Sie uns

ToolParts-Service

Kleinhaslach 35
90599 Dietenhofen

Kontakt

Technischer Support:

 

Rufen Sie einfach an

0049(0) 98 72 / 95 66 61 0 oder nutzen Sie unser Kontaktformular.

Mitglied im Händlerbund
Landbell AG
Druckversion Druckversion | Sitemap
© ToolParts-Service